BC Battery Controller K612 Battery Charger, Maintainer and Reconditioner for all 6V & 12V lead-acid batteries - Jaws Motorcycles

BC K612 BC K612 is the all-in-one battery charger and maintainer for all 6/12V lead-acid batteries (including sealed/MF batteries, gel batteries and AGM batteries). With a single device, it is possible to recharge and maintain both 12 Volt batteries installed on daily used vehicles (motorcycles, cars, etc) and 6 Volt batteries mounted on classic cars […]
BC K612 BC K612 is the all-in-one battery charger and maintainer for all 6/12V lead-acid batteries (including sealed/MF batteries, gel batteries and AGM batteries). With a single device, it is possible to recharge and maintain both 12 Volt batteries installed on daily used vehicles (motorcycles, cars, etc) and 6 Volt batteries mounted on classic cars and motorbikes, which are generally used rarely and subjected to battery maintenance issues. BC K612 can be left always connected to the battery for an indefinite time, as long as the vehicle is unused: it is for an oldtimer event or for a summer trip, your classic car or classic motorcycle will always be ready to start.   FEATURES * 2 programs: 6 Volt / 12 Volt * Maximum charging current: 1 Amp * 8-steps charging algorithm: initialization, recovery (from 1.25V for 12V batteries, from 0.63V for 6V batteries), soft charge, bulk charge, desulfation, analysis, maintenance and equalization * Protections: polarity inversion, short circuit, overcharging, overheating. No sparks * Battery types: 6/12V lead-acid (traditional, gel, MF, AGM, EFB, VRLA, Ca/Ca) * It verifies if the battery is able to retain its charge   TECHNICAL DATA Input Voltage: 220÷240V ac, 50-60Hz Output Voltage: 6.9V/7.2V - nom. 6V / 13.8V/14.4V - nom. 12V Charging Current: 1 A max Battery Capacity: 1.2 - 100 Ah Operating Temperature: -20°C - +50°C Size: 130 x 90 x 53 mm CHARGING PROGRAM SELECTION 1. Charging Program Selection Once you connected the battery charger to the power outlet, a LED will show you the active charging mode (6V or 12V). To change the charging mode, please follow this procedure: 1. With the device disconnected from the battery and from the power outlet, connect the clamps to the device and put the red and the black clamps together (creating a permanent short circuit). 2. Connect the device to the power outlet. The active charging mode will change and it will be displayed by the correspondent LED (6V or 12V). 3. Disconnect the device from the power outlet and separate the clamps. The selected charging mode will be kept in memory until you repeat this procedure. 2. Recharging, Reconditioning and Mantenance - 100% automatic and complete Once the right charging program for your battery is selected, just connect BC K612 to the battery to make the 8-steps full-automatic charging procedure start. BC K612 brings your battery to the maintenance phase, recovering it gently if necessary, giving it energy and power during the charging and desulfation steps and keeping it constantly under control, from the initial test to the end-cycle battery analysis. 8 CYCLES CHARGING TECHNOLOGY BC K612 is managed by a latest-generation microprocessor, which is in charge of monitoring the battery parameters in real time and to execute a new multi-cycle charging algorithm: 1. Initialization: the device checks if one or more cells are shorted, in order to verify that the battery is in a proper condition to be recharged/recovered. 2. Recovery: if the battery is deep discharged (battery voltage starting from 1.25V for 12V batteries, 0.63V for 6V batteries), the device tries to recover it, taking it back to a higher voltage. 3. Soft Charge: if the battery is in a condition of significant undercharge, the device provides a light pulsing current to the battery, to overcome this critical phase. 4. Bulk Charge: the device provides full current to the battery, recovering about 85-90% of the battery capacity. 5. Desulfation / Absorption: the device provides a controlled overcharge to recover the remaining 10-15% of the battery capacity, through the desulfation/recovery the lead-acid cells (for low or medium sulfation). 6. Battery Analysis - End Cycle Test: the device stops providing current to the battery for a short time, in order to verify whether the battery is able to retain the charge received. This test is periodically repeated during the Maintenance. 7. Maintenance: the device keeps the battery in the best charge conditions for very long periods (even months) during which your vehicle is left unused, without any possible drawback (battery overcharge, battery overheating, water and/or electrolyte loss, etc). 8. Equalization: every 30 days during long term maintenance, the device executes an equalization charge in order to balance the battery lead-acid cells, avoiding electrolyte stratification within the cells. SAFETY AND PROTECTIONS BC K612 features a series of 8 protections and active guard mechanisms that make it easy to install and to use, without any risks even for users without expertise: - No interferences the vehicle's on board electronics (control unit, ABS, GPS) - Protection from output lines short circuit, even for an indefinite time: no sparks! - Protection from battery polarity inversion - Protection from battery overcharge/overheating - Thermal protection from overtemperature - No need to disconnect the battery from your vehicle - Very few gas development during the charge: no need to remove the battery plugs Laboratory Tests ensure the manufacturing of products in conformity to the regulations in force on safety and electro-magnetic compatibility. Norms and Regulations: IEC-61000-3-2(ed.3);am1;am2, IEC-61000-3-3(ed.2), CEI-CISPR14-1(ed.5);am1;am2, CEI-CISPR14-2(ed.1);am1;am2, IEC60335-1(ed.5), IEC-60335-2-29(ed.4);am1;am2. BATTERY TYPES AND CAPACITY BC K612 is specifically designed for charging and maintaining all 6/12V lead-acid batteries currently available on the market (traditional, VRLA, MF, AGM, GEL, Ca/Ca, etc). BC K612 is addressed to recharge and maintain batteries with a capacity from 1.2 to 100 Ah. EQUIPMENT & ADD-ONS The package includes: - the battery charger and maintainer BC K612 for long term battery maintenance, provided with a power input cable (2 meters long) and a battery output cable; - a waterproof battery connection cable with eyelets, which can be left always installed on board; - a battery connection cable with insulated clamps; - according to the selected kit, a universal 12/18mm cigar socket adapter may be included; - a copy of the User Manual.

BC K612 motorcycle battery charger and maintainer – bcbattery.us

KATBO Automatic Battery Charger 12V 6V Auto-Voltage Detection, Automotive Battery Charger 2Amp 6 Amp Lead Acid Batteries Float Charger Maintainer for Motorcycle Car Boat Marine Lawn Mower ATV Toy Car

LST Trickle Battery Charger Automatic Maintainer 6V 12V Smart Float for Auto Car

2A 6V/12V Fully Automatic Battery Charger and Maintainer - Schumacher Electric

ExpertPower 12V 20A Lead-Acid Battery Charger : Automotive

EverStart MAXX 3 Amp 6V/12V Automotive Battery Charger (BC3E) - New

Cobra Battery Charger 2A - 6V/12V Battery Charger & Maintainer with Battery Clamps & Ring Terminals for Cars, SUVs, Motorcycles and Boats

KATBO Battery Charger 12V 6A 6 Volt 2A Trickle Battery Charger Maintainer Float Charger for Motorcycle Car Boat Marine Lawn Mower ATV Toy Lead Acid,AGM, Gel,STD,SLA (Yellow) : Automotive

Cobra 2-Amp Smart Charger & Battery Maintainer - 6V and 12V Portable Power, Stay charged all year long!, The Cobra Fully Automatic Battery Charger 2A